The term base station can be used in the context of land surveying, wireless computer networking, and wireless communications.
In the context of external land surveying, a base station is a GPS receiver at an accurately-known fixed location which is used to derive correction information for nearby portable GPS receivers. This correction data allows propagation and other effects to be corrected out of the position data obtained by the mobile stations, which gives greatly increased location precision and accuracy over the results obtained by uncorrected GPS receivers.
In the area of wireless computer networking, a base station is a radio receiver/transmitter that serves as the hub of the local wireless network, and may also be the gateway between a wired network and the wireless network. It typically consists of a low-power transmitter and wireless router.
In radio communications, a base station is a wireless communications station installed at a fixed location and used to communicate as part of either:
In professional two-way radio systems, a base station is used to maintain contact with a dispatch fleet of hand-held or mobile radios, and/or to activate one-way paging receivers. The base station is one end of a communications link. The other end is a movable vehicle-mounted radio or walkie-talkie. Examples of base station uses in two-way radio include the dispatch of tow trucks and taxicabs.
Professional base station radios are often one channel. In lightly-used base stations, a multi-channel unit may be employed. In heavily-used systems, the capability for additional channels, where needed, is accomplished by installing an additional base station for each channel. Each base station appears as a single channel on the dispatch center control console. In a properly designed dispatch center with several staff members, this allows each dispatcher to communicate simultaneously, independently of one another, on a different channel as necessary. For example, a taxi company dispatch center may have one base station on a high-rise building in Boston and another on a different channel in Providence. Each taxi dispatcher could communicate with taxis in either Boston or Providence by selecting the respective base station on his or her console.
In dispatching centers it is common for eight or more radio base stations to be connected to a single dispatching console. Dispatching personnel can tell which channel a message is being received on by a combination of local protocol, unit identifiers, volume settings, and busy indicator lights. A typical console has two speakers identified as select and unselect. Audio from a primary selected channel is routed to the select speaker and to a headset. Each channel has a busy light which flashes when someone talks on the associated channel.
Base stations can be local controlled or remote controlled. Local controlled base stations are operated by front panel controls on the base station cabinet. Remote control base stations can be operated over tone- or DC-remote circuits. The dispatch point console and remote base station are connected by leased private line telephone circuits, (sometimes called RTO circuits), a DS-1, or radio links. The consoles multiplex transmit commands onto remote control circuits. Some system configurations require duplex, or four wire, audio paths from the base station to the console. Others require only a two-wire or half duplex link.
- minimum receiver specifications and filtering.
- analysis of other frequencies in use nearby.
- in the US, coordination of shared frequencies by coordinating agencies.
- locating equipment so that terrain blocks interfering signals.
- use of directional antennas to reduce unwanted signals.
Base stations are sometimes called control or fixed stations in US Federal Communications Commission licensing. These terms are defined in regulations inside Part 90 of the commissions regulations. In US licensing jargon, types of base stations include:
- A fixed station is a base station used in a system intended only to communicate with other base stations. A fixed station can also be radio link used to operate a distant base station by remote control. (No mobile or hand-held radios are involved in the system.)
- A control station is a base station used in a system with a repeater where the base station is used to communicate through the repeater.
- A temporary base is a base station used in one location for less than a year.
- A repeater is a type of base station that extends the range of hand-held and mobile radios.
Amateur and hobby
In Amateur radio, a base station also communicates with mobile rigs but for hobby or family communications. Amateur systems sometimes serve as dispatch radio systems during disasters, search and rescue mobilizations, or other emergencies.
An Australian UHF CB base station is another example of part of a system used for hobby or family communications.
Wireless telephone differ from two-way radios in that:
- wireless telephones are circuit switched: the communications paths are set up by dialing at the start of a call and the path remains in place until one of the callers hangs up.
- wireless telephones communicate with other telephones usually over the public switched telephone network.
A wireless telephone base station communicates with a mobile or hand-held phone. For example, in a wireless telephone system, the signals from one or more mobile telephones in an area are received at a nearby base station, which then connects the call to the land-line network. Other equipment is involved depending on the system architecture. Mobile telephone provider networks, such as European GSM networks, may involve carrier, microwave radio, and switching facilities to connect the call. In the case of a portable phone such as a US cordless phone, the connection is directly connected to a wired land line.
While low levels of radio-frequency power are usually considered to have negligible effects on health, national and local regulations restrict the design of base stations to limit exposure to electromagnetic fields. Technical measures to limit exposure include restricting the radio frequency power emitted by the station, elevating the antenna above ground level, changes to the antenna pattern, and barriers to foot or road traffic. For typical base stations, significant electromagnetic energy is only emitted at the antenna, not along the length of the antenna tower.
Because mobile phones and their base stations are two-way radios, they produce radio-frequency (RF) radiation in order to communicate, exposing people near them to RF radiation giving concerns about mobile phone radiation and health. Hand-held mobile telephones are relatively low power so the RF radiation exposures from them are generally low.
The consensus of the scientific community is that the power from these mobile phone base station antennas is too low to produce health hazards as long as people are kept away from direct access to the antennas. However, current international exposure guidelines (INCIRP) are based largely on the thermal effects of base station emissions. Some scientists have questioned whether there are non thermal effects from being exposed to low level RF such as are transmitted from mobile phone base stations. Such 'non-thermal' effects include how the actual frequencies interfere with the human brain and all other cells in the human body.
Two GSM mobile phone base station towers disguised as trees in Dublin, Ireland.
|Wikimedia Commons has media related to: Base station|
- Base Transceiver Station
- Mobile Switching Center
- Access point base station
- Cell site
- Cellular repeater
- Mobile phone
- Mobile phone radiation and health
- Portable phone
- Signal strength
- Audio level compression
Onslow, David. "Two-Way Radio Success: How to Choose Two-Way Radios, Commercial Intercoms, and Other Wireless Communication Devices for Your Business.". IntercomsOnline.com. http://wirelessintercomsonline.com/downloads/freebook.htm. Retrieved 2008-09-07.
- "Evaluating Regional Alternatives: Systems Design Considerations," Planning Emergency Medical Communications: Volume 2, Local/Regional Level Planning Guide, (Washington, D.C.: National Highway Traffic Safety Administration, US Department of Transportation, 1995) pp. 39-43.
- Block diagram is from: "Figure 2: Two Channel VHF Base Station," Planning Emergency Medical Communications: Volume 2, Local/Regional Level Planning Guide, (Washington, D.C.: National Highway Traffic Safety Administration, US Department of Transportation, 1995) pp. 42.
- Base stations in land mobile systems are often located at remote sites such as hilltops or water towers. Some are controlled from two or more locations. For example, a base station used to communicate with taxis may be connected to remote control consoles at both a taxi company office and an answering service for after-hours calls. The taxi company and answering service may be miles apart. Single channel base stations reduce confusion by eliminating the possibility that the wrong channel may be selected.
- To read more about multi-channel consoles, look at the service manual for a relatively simple console: 8-Channel Remote Console, 120, 220, 240 V AC or 12 V DC T16167 AM or BM, 68-81021E80, (Schaumburg, Illinois: Motorola, Inc. 1980.) This is a relatively simple analog console compared to large, enterprise-level Centracom-series units.
- The term RTO circuit is legacy jargon and comes from Bell System billing terminology. RTO circuits refer to analog radio remote control and radio broadcast leased telephone circuits.
- For a brief discussion of remote controlled base stations, see: "Evaluating Regional Alternatives: Systems Design Considerations," Planning Emergency Medical Communications: Volume 2, Local/Regional Level Planning Guide, (Washington, D.C.: National Highway Traffic Safety Administration, US Department of Transportation, 1995) pp. 39-41. Tone remote controls are described in this section.
- Block diagram is from: "Figure 8: Bandpass Cavity/Isolator Location," Planning Emergency Medical Communications: Volume 2, Local/Regional Level Planning Guide, (Washington, D.C.: National Highway Traffic Safety Administration, US Department of Transportation, 1995) pp. 57.
- Bulleted items condensed from, "EMS Communications," "System Coordination," and "Site Engineering," in Planning Emergency Medical Communications: Volume 2, Local/Regional Level Planning Guide, (Washington, D.C.: National Highway Traffic Safety Administration, US Department of Transportation, 1995) pp. 10-19, 55-58.
- For an example of receiver specifications, see, "Table 9-3," 800 MHz Trunked Radio Request for Proposals: Public Safety Projects Office, (Oklahoma City, Oklahoma: Oklahoma City Municipal Facilities Authority, 2000, pp. 181.
- A list of types of filtering used to prevent interference between equipment at the same site is included in "6.2.4 Electromagnetic Compatibility Studies," 800 MHz Trunked Radio Request for Proposals: Public Safety Projects Office, (Oklahoma City, Oklahoma: Oklahoma City Municipal Facilities Authority, 2000, pp. 119.
- More detail of interference reduction equipment is provided in, "9.1.2 Base Station/Mobile Relay, 800 MHz," 800 MHz Trunked Radio Request for Proposals: Public Safety Projects Office, (Oklahoma City, Oklahoma: Oklahoma City Municipal Facilities Authority, 2000, pp. 165-168.
- For example, US federal government systems are coordinated and licensed by the National Telecommunications and Information Administration. Business/Industrial Pool licenses are coordinated by the Personal Communications Industry Association (PCIA) and licensed by the Federal Communications Commission.